Nexus Mechanism Driver Overview and Architecture¶
The ML2 Nexus driver adds and removes trunk vlans on the Cisco Nexus switch for both ethernet interfaces and port-channel interfaces. It also supports configuration of VXLAN Overlay, baremetal deployments (VLAN configurations only), and performs configuration replay on switch recovery.
This user guide describes the activities the Nexus driver performs to create and remove VLANS on receipt of OpenStack ML2 baremetal and non-baremetal port events.
When VMs are created or when subnets are created with dhcp is enabled, port events are received by the Nexus driver. If there are switch credentials defined by the administrator for the event, then the Nexus driver will process the event.
The basic Nexus configuration actions taken by the Nexus driver are as follows:
- Configure the provided VLAN on the Nexus device,
- Configure the interface as switchport mode trunk and switchport trunk allowed vlan none if no trunk vlans have been configured manually by the user.
- Add a trunk vlan onto the specified interface using the interface CLI switchport trunk allowed vlan add <vlanid>.
- For baremetal port events, if the port is the parent port to an OpenStack trunking configuration or not a participant of an OpenStack trunking configuration, the VLAN is also configured as native using the CLI switchport trunk native vlan <vlanid>.
Both normal VM port events and baremetal port events are supported by the Nexus Driver for VLAN creation. They can co-exist at the same time.
In the case of non-baremetal port events, the Nexus driver uses the
host name from the port event to identify a switch and interface(s)
to configure. The vlan used to configure the interface also comes
from the port event. The administrator configures the host to
interface mapping as well as switch credentials in the ML2 Nexus
Driver switch configuration section of the neutron config file.
(ref: section header
ml2_mech_cisco_nexus of config file shown
in the Nexus Mechanism Driver Administration Guide.)
In the case of baremetal port events, the switch and interface mapping
are contained in the event itself. The Nexus driver learns the
host to interface mapping by using dns name as the host name. If
dns is not enabled, then the host name defaults to
Even though the administrator does not configure this mapping,
the switch credentials must be configured for baremetal events.
This configuration aides in determining whether the baremetal
event is for the Nexus Driver.
If there are multiple ethernet interfaces defined in the baremetal event, this implies it is a port-channel. When the Nexus driver detects multiple interfaces, it next determines whether the interfaces are already configured as members of a port-channel. If not, it creates a new port-channel interface and adds the ethernet interfaces as members. In more detail, it will do the following:
- Allocate a port-channel id from
vpc_poolconfigured by administrator ref:
vpc_poolvariable in admin and config guides).
- Create the port-channel which includes switchport mode trunk, switchport trunk allowed vlan none, and vpc-id x.
- Apply either user customized port-channel config provided by
administrator OR the default config spanning-tree port type edge
trunk and no lacp suspend-individual
intfcfg_portchannelvariable in the Nexus administration and configuration guides).
- Apply channel-group <vpcid> force mode-active to the ethernet interfaces to make each interface a member of the port-channel.
Regardless whether the port-channel is learned or created, the trunk vlans are applied to the port-channel and inherited by ethernet interfaces.
When a VM is removed or a subnet is removed and dhcp is enabled, a delete port-event is received by the Nexus driver. If the port exists in the Nexus driver’s port data base, the driver will remove it from the data base as well as remove the trunk vlan on the Nexus device.
To remove the trunk vlan from interface on the Nexus switch, it sends switchport trunk allowed vlan remove <vlanid> and possibly no switchport trunk native vlan <vlanid> if it was sent during vlan creation. The driver then checks if the vlan is used on any other interfaces. If not, it will remove the vlan from the Nexus switch as well by issuing no vlan <vlanid>.
If a port-channel was previously created for baremetal port events as described in VLAN Creation and if there are no more port-bindings referencing the created port-channel, the Nexus Driver will do as follows:
- The ethernet interfaces will be removed as members to the port-channel by issuing :command:’ no channel-group ‘ on each participating Nexus Switch interface,
- The port-channel will be completely removed from the Nexus Switch(s) by issuing no port-channel <id> on each participating switch,
- And the port-channel/vpc id released back into the Nexus driver vpc-id pool.
VXLAN Overlay Creation¶
VXLAN Overlay creation does similar basic vlan trunk config as described in the VLAN Creation section. Prior to doing vlan trunk config, the VLAN is mapped to a VXLAN Network Identifier (VNI) and applied to the NVE (network virtualization edge) interface. Specifically, the steps done for the user is as follows:
Create a one-to-one mapping by creating a mulitcast IP address and associating it with a VXLAN Network ID. Apply this configuration to the NVE interface:
int nve1 member vni <vni-id> mcast-group <mcast-addr>
Associate the VNI segment to the VLAN segment. The configuration applied is as follows:
vlan <vlanid> vn-segment <vni-id>
Configuration VXLAN VNI ranges and multicast groups is done beneath
the section header
ml2_type_nexus_vxlan of the configuration file.
See the Nexus Mechanism Driver Administration Guide for more details.
VXLAN Overlay Removal¶
VXLAN Overlay removal does vlan trunk removal as described in VLAN Removal section. Additionally, it removes the vni member from the nve interface as well as vlan segment if there are no other ports referencing it.
If the Nexus MD discovers the Nexus switch is no longer reachable, all known configuration for this switch is replayed once communication is restored. The order of the events are performed differently than described in VLAN Creation for efficiency reasons. This order is as follows:
- All known interfaces are initialized with switchport mode trunk and switchport trunk allowed vlan none if there are no trunking vlans already configured.
- For VXLAN, set member vni <vni-id> mcast-group <mcast-addr> beneath the nve interface.
- For each interface, a lists of VLANS are sent to the Nexus switch as a single request using the configuration switchport trunk allowed vlan add <multiple-vlanids>.
- Following this, batches of vlans made active. For VXLAN, this will also include the vn-segment <vni> configuration.